The Geiszler is a stepped adapter designed to work with every thru-axle fitment currently on the market: 12x142, 12x150, 15x100, 20x110, Lefty and 24 Maverick. The tool will allow precision dishing without removal, a notable time saver when wheel building. The Geiszler can be bolted into the hub with the included stud for serious wheel work. It can also be slipped into place for minor adjustments and retained by the compression of the truing stand. This simple tool eliminates clutter around your truing stand and keeps you from searching for the right adapter. - Made in Bend, Oregon - Bolts and washers for use with single-armed wheel stands are available upon request, for free
We went through extra steps to make this tool half precision measuring instrument and half pry bar. - Tolerances as tight as a quarter of a thousandth of an inch (.0063mm) in some critical dimensions of this tool. - Ability to lock in the feeler so you don't have to second-guess your measurement after bumping it on the tire. - Top half of tool will rotate out of the way of fender stays and frame tubes. - Feeler gauge stick stores inside the top half of the tool, very handy for the traveling mechanic. - T-bolt extends past the tool for access to those problematic hangers found on some modern full suspension bikes. - Compact at just under 11" ( 28cm) - Re-buildable - While ideally your HAG should be sent back for a rebuild, it is possible to do them in the field by replacing the brass bushing in the T-Bolt. - Compatible with the three most common wheel sizes (26, 27.5/650B, and 700/29)
This dishing gauge is fully machined from big billets of aluminum to a final shape and accuracy that's as nice to use as it is to look at. Compatible with wheels from 20-29 inches and all hub combinations. Standoff feet are included for checking dish with the tire in place, even the big fat ones. The gauge uses a unique spring-loaded mechanism to drop the plunger. Press that little brass button on the front and the plunger will drop to the face of the hub. No archaic time-sucking threaded indicators here!
This bottom bracket socket is for use with E Thirteen's BB30 bottom brackets. Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket.
This bottom bracket socket is for use with Hope's BSA30 bottom bracket. Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket.
This bottom bracket socket is for use with the Praxis M30 bottom bracket. Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket.
Bearing drift designed for the SRAM DUB crank platform and use with the Abbey Bike Tools Modular bearing press. SRAM recently launched a new crank platform called DUB to improve bearing durability and compatibility that modern frames have dictated. This 28.99mm spindle and its press fit bottom bracket requires some special drifts to install correctly. We worked with the crew at SRAM to develop tools for this and came up with some simple and important tweaks from a standard bearing drift. These drifts have a tapered boss that forces the small O ring into its gland. A normal drift with a square boss can easily tear the fragile O ring that helps with bearing durability. So this basic modification makes sure your bottom bracket retains the durability it was designed to have. - Comes as a set of two drifts
The Shop Hammer has a heat-treated 1.5-inch (38mm) stainless steel head and 12-inch long handle with the same silicone grip from ESI as our Team Issue Hammer. Weighing in at a respectably stout 20oz (566g), they are sure to make short work of setting crown races and removing press fit bottom brackets. - Hammer comes standard with green soft face. Brass tips are also available. - Made in Bend, Oregon
This tool is compatible with all outboard bearing cups that our dual-sided Shimano socket doesn't fit, including Campagnolo, SRAM, FSA, and older Shimano. These gems start as a 7075 aluminum billet and get precisely machined. We take the time to put some nice deep finger splines in this tool so you can thread the cup into the frame by hand with those greasy fingers you haven't washed in a while. - Hard anodized and laser-engraved with torque specs. - Use your favorite 3/8" square drive ratchet or torque wrench to tighten it down.
The Stu Stick is a 44-gram rotor truing tool. Whether you want to slip it into your hydration pack for that enduro mountain bike ride or travel the world working with one of the staples of cross racing, it's up to the task. You can even use it to crack open a beer after you're done with the day's fun. - Weight: 44g - Made of aluminum
$30.00 - $130.00
Suspension service is a specialty within bicycle repair, and it takes specialized tools to perform this work. One of the things that any factory tech will tell you is nice to have are sockets specifically made or altered for the low profile hex on the top of each fork leg. The lead-in or chamfer on a standard socket will greatly decrease the contact between tool and part and can easily scratch or deform those nuts. For years shops have been grinding down their sockets to remove the chamfer. The problem is that you're still often left with a loose-fitting socket that is still prone to chewing up those delicate parts. That's why we started from scratch. We made our sockets from billet aluminum to exacting tolerances to keep these parts in good shape. Fully CNC-machined with zero lead-in, they make the specialty that is suspension service a little bit easier. They feature a 3/8" square drive for use with your favorite torque wrench as well as finger splines to help run the top caps into the fork legs with those oil soaked hands. We also kept them short (1" or 25mm for all sizes) to reduce the chance of them slipping off of the top cap under torque. - Made from billet aluminum to exacting tolerances to keep form damaging the suspension - Finger splines so you can thread it easily by hand - 3/8" square drive - Short (1"/25mm for all sizes) to reduce the chance of them coming off of the top cap under torque - Made in Bend, Oregon Applications - 24mm socket - used on SRAM top caps - 26mm socket - used on Marzocchi and Reverb sealheads - 27mm socket - used on Fox and X-Fusion top caps - 30mm socket - used on the RS-1 SRAM sealhead removal tool as well as a handful of other forks. - 6-size set covers most modern suspension forks on the market: 24, 26, 27, 28, 30 and 32mm
Coming in at roughly 265 grams, the Team Issue Titanium Hammer is a big weight savings over more traditional hammers. The soft face is replaceable with commonly available 1" threaded faces. At 12" long, it's compact but still long enough to remove those stubborn bearings. We finish off the Team Issue hammer with a custom silicone grip from ESI to give a bit of cushion from the all-metal construction.
Page 1 of 1