Tools

Designed to press in all current wheels mfg bottom brackets! our universal bottom bracket frame drift is designed to press all current wheels mfg bottom bracket cups in to your frame. The adapter is machined with multiple steps to fit common bottom bracket shell inside diameters listed in the compatibility tab below. Each step is laser etched with the diameter size. Drift can also can be used as a frame bottom bracket shell sizing guide! - Inner hole sized to fit 1/2" threaded rod. (Not for use with our Press-1 or Press-4 ) - Compatible with any other press with a 1/2" diameter rod - Recommended for use with Wheels Mfg BP0006, BP0007 - Machined aluminum - Anodized red - Sold individually We do not recommend it for use with press with a rod diameter less than 1/2". When used with a smaller rod, it is almost impossible to prevent the cups or bearings from pressing in straight.

Our GXP-LEFT open bore adapter is used to press 22x37 sealed bearings into SRAM GXP bottom bracket cups and direct fit frames like trek BB90. The adapter is machined with one step at 22mm OD, which fits into the center of the sealed bearing. - Installs: 22x37 (GXP) bearing - Inner step outer diameter: 21. 9mm - Outer diameter: 36. 8mm - Thickness: 7mm - Thru hole diameter: 0. 387" (9. 8mm) - Inner hole sized to fit 1/2" ACME threaded rod - Compatible with BP0006, BP0007 - Machined, red anodized aluminum - Sold individually

Our 6806 open bore adapter is used to press 42x30 sealed bearings. The adapter is machined with one step at 30mm ID, which fits into the center of the sealed bearing. Common bearing size for BB30 frames and bottom brackets. - Installs: 6806 bearing - Inner step outer diameter: 29. 9mm - Outer diameter: 41. 8mm - Thickness: 7mm - Thru hole diameter: 0. 387" (9. 8mm) - Inner hole sized to fit 1/2" threaded rod - Compatible BP0006, BP0007 - Machined, red anodized aluminum - Sold individually (2 drifts required for some installations)

- Essential bearing press for installation of bearings with a 10mm minimum ID - (1) 3/8 ACME threaded rod, (2) 30mm standoffs, (2) threaded handles

This 7-piece adapter set is used to install 22mm and larger inside diameter sealed bearings into bottom brackets. Includes adapters for the most common bottom bracket bearings for Shimano outboard cup BBs (HollowTech II), SRAM GXP, Truvativ, FSA, PF30 and BB30 bottom bracket bearings. - Includes open bore drifts for 6805, 24x37, BB30, PressFit30, GXP and BB86 bearings - 10mm ID hole, for use with Wheels Manufacturing bearing press handles - Compatible with Wheels Mfg. PRESS-1 or PRESS-4 handles

BB30 service kit for SRAM DUB cranks. - Includes (2) Enduro 6806/29 ABEC-3 sealed bearings and 2 retaining clips - Bearing Dimensions: OD: 42mm / ID: 29mm / Width: 7mm - Enduro ABEC-3 bearings - Use with SRAM DUB cranks Note: SRAM DUB cranksets are not designed to work in 68mm or 73mm wide shells with inboard bearings. Use only if your frame is a direct-fit bearing system, and the BB shell width is 86.5mm or wider.

Wheels Manufacturing Sealed Bearing Extractor - 15mm Fits the following bearings: - 6002 - 6702 - 6802 - 6902 - 15267 - 15268

This do-it-all universal bottom bracket press is designed to press in all current Wheels Mfg. bottom brackets. Economical and easy to use, this tool is made up of two machined aluminum handles, a 1/2-inch threaded rod, and two machined aluminum drifts. Each drift is machined with multiple steps to fit common bottom bracket shell and bearing diameters. No more searching for the correct size drifts and parts—just match up the drift to your frame's BB shell size and your bottom bracket's bearing size, and press away. - Zinc-plated 1/2-inch diameter threaded rod resists bending, allowing for the cups to align and press in straight - Drifts can also can be used as a frame bottom bracket shell sizing guide - Machined aluminum handles and drifts - Red anodized drifts and handles - Steps on drift are marked with diameter sizes - Works with BB shells up to 132mm wide - Includes two universal BB drifts

- Machined to match manufacturer specifications and designed to be used with a 1/2" drive socket or torque wrench for easy installation and removal of e-bike lockrings. - Precision machined aluminum body. - Anodized in Wheels MFG red.

Easy-to-use tool removes and installs replacement bushings in suspension and shock pivots. Includes retaining tool, top cap, and three sizes of bushing drifts. - Fits eyelet sizes - 10mm, 12mm, and 1/2" - Machined aluminum - Anodized Red